Canadian Standards Association (CSA) 178.2 Level 1 Practice Exam

These questions are part of the practice quiz. Start practicing

• Which arc-start method for GTAW has the highest cost?
• CSA Standard Z662 requires the approval of welding procedure specifications by:
• Which engineering field is not covered by ISO?
• How should the inspector address pets or occupants during an inspection?
• E4914 electrodes are a designation used for which of the following?
• A gap of 2 mm or greater in a fillet weld has what effect on the fillet size?
• A specified curvature in the plane of the flange is known as:
• Most standards are generated by voluntary efforts of government, industry, etc.
• Argon-rich shielding gas promotes the finger-like penetration profile in GMAW.
• Which standard is cited for the approved use of Standard Welding Procedure Specifications among CSA B51, AWS D1.1, and ASME IX?
• Common shielding gases used for the GTAW process are?
• Which statement best describes the purpose of a welding procedure specification (WPS) within CSA W47.1?
• How should post-inspection communications with clients be handled?
• The basic oxygen furnace is used to produce pig iron. True or False?
• When cosmetic issues are present, how should they be documented in the report?
• How many principal views are there in an orthographic projection?
• Which interior features are typically inspected?
• The term 'basic' in the basic oxygen furnace refers to the chemical nature of the refractory lining.
• What is the purpose of the limitations section in the report?
• A CSA W47.1 Div. 1 certified company requires the full time employment of a Welding Engineer.
• Which statement best describes absorbed moisture testing for welding electrodes?
• If a camber diagram is specified, camber should be checked at multiple points rather than a single point.
• If a welder has qualified with a group F2 electrode, the welder is qualified to weld with which electrodes?
• Welding tests for pressure vessel equipment fabricated outside Canada shall be accepted only if approved by an authorized inspection agency approved by the regulatory authority in the country where manufacturing occurred.
• If an electrode is labeled E7018-R, which of the following is true?
• Which statement is true about the R suffix in electrode designations?
• Under Level 1 guidelines, when is it appropriate to identify refrigerant or fuel types?
• CSA W59 Welded Steel Construction is primarily for which material?
• Tempering martensite involves reheating to a temperature:
• Camber diagram check: True or False? If a camber diagram is specified it is necessary to check camber at one point only.
• If a mold concern is suspected but not confirmed, which statement is most appropriate for the inspector's report?
• Which components are typically included in a Level 1 inspection scope?
• Which option best describes a code system for electrodes in major standards?
• How should a conflict of interest be managed?
• What type of current is used to detect subsurface defects when using a magnetic particle test?
• Which CSA standard would you consult for aluminum construction welding?
• The document adopted as the source for standard terms and definitions in welding and joining was officially adopted by the standards writing bodies of which country?
• Is the leg length of a concave fillet weld the same as the weld size?
• Quality assurance is best described as:
• CSA B51, AWS D1.1 and ASME IX all refer to which standard for the approved use of Standard Welding Procedure Specifications?
• What is the recommended frequency for educational or professional development for inspectors?
• A welding arc is intensely hot, with temperatures exceeding?
• When labeling photos in the report, which detail should be included?
• Which standard gives the requirements for oil and gas pipeline systems?
• In a Level 1 inspection, exterior drainage is evaluated by observing which factors?
• Which statement best describes the purpose of quality assurance in manufacturing?
• CSA W59 Welded Steel Construction is considered to be which type of standard?
• What should the executive summary include in the inspection report?
• Which of the following is a consequence of the R designation on an E7018-R electrode?
• What equipment might a Level 1 inspector typically use?
• In the E7018-R designation, the R indicates compliance with what kind of testing?
• The positive terminal of an electrical circuit is called what?
• What is the purpose of continuing education for inspectors?
• How should time stamps be handled in the inspection report?
• How should the inspector handle party walls or common area issues?
• Why must European drawings be studied carefully before fabrication parts?
• Which type of porosity usually occurs with an orientation perpendicular to the weld face?
• Are destructive electrical tests allowed in Level 1 inspections?
• Which statement about E7018-R is correct?
• The engineering field not covered by ISO is?
• How should inaccessible areas be handled in the report?
• 1% lanthanated GTAW electrodes are color coded as which color?
• Which of the following statements correctly describes a hypoeutectoid steel's carbon content?
• Which section of the ASME Boiler and Pressure Vessel Code covers Nonferrous Material Specifications?
• What does WPDS stand for in CSA W47.1?
• How should documentation retention be handled?
• Which ASME BPVC Section lists base and filler metal specifications that are permissible for use in qualifying welders and procedures?
• If you see E7018-R on a welding electrode, you should anticipate what testing requirement?
• According to CSA W59, within what distance of the weld must surfaces be free of slag, rust, and paint to prevent contamination?
• Gamma radiation emitted by a Co-60 source has wavelengths longer than those from Ir-192. Which statement is correct?
• How should invasive testing be treated in Level 1 inspections?
• Inaccessible areas: how should they be addressed in Level 1 reporting?
• In a Level 1 inspection, how should plumbing systems be evaluated?
• Which standard is classified as a fabrication standard rather than a design standard?
• Which observation best demonstrates non-invasive moisture intrusion?
• When evaluating HVAC, should the inspector observe operating condition, and under what condition?
• What information should be included in the pre-inspection disclosure?
• Which statement best describes the typical scope of a Level 1 inspection?
• The three major steel groups are carbon steels, low-alloy steels and:
• The plates for the shell of a pressure vessel are usually formed with the rolling direction in which orientation?
• What is the definition of a low-hydrogen electrode?
• Why must surfaces within the specified distance of the weld be free of slag, rust, and paint?
• Which statement is true about moisture-related designations such as the R suffix on electrodes?
• Which standard includes ferrous and non-ferrous materials with notch toughness requirements and includes aluminum piping systems?
• A common shielding gas for GTAW is?
• Which organizations’ standards recognize the electrode identification system described in A5.01–A5.36?
• What is the main reason to study European drawings?
• What does the acronym WPS stand for in the context of welding procedures?
• True or False? Normalizing of steel involves heating into the fully austenite region followed by furnace cooling.
• How should accessory energy-efficient features be treated in the report?
• Which statement is NOT part of evaluating exterior drainage in a Level 1 inspection?
• A welding supervisor under CSA Standard W47.1 shall have a minimum of how many years of experience, assuming no reduction has been granted based on education and experience?
• When up to 0.8% carbon is added to iron, the resulting steel under equilibrium conditions will have the structure of:
• Which statement best describes how moisture signs are identified in interior spaces during Level 1 inspection?
• What is the system that ASME, ASTM, and AWS standards recognize for electrode identification?
• Which statement best describes how weather-related accessibility limitations should be documented in the inspection report?
• In Canada, the national body that approves standards is the:
• Are invasive tests or disassembly allowed in a Level 1 inspection?
• How is moisture intrusion typically detected non-invasively?
• The finger-like penetration profile with GMAW is promoted by which shielding gas?
• How should cosmetic issues be presented in the report?
• In magnetic particle testing, which option best describes the purpose of using direct current?
• Which document has been officially adopted by the standards writing bodies of Canada as the source for standard terms and definitions in welding and joining?
• Hot rolling is carried out:
• What does CSA 178.2 emphasize about the limitations of a Level 1 inspection?
• When deviations from drawings and specifications are warranted, deviations should be:
• An SFA designation before a filler metal specification (such as SFA-5.4) means:
• The numeric portion of the electrode designation E4918-X denotes a minimum tensile strength in MPa.
• The maximum combined warpage and tilt of a flange permitted by CSA W59 is:**
• The R suffix on an E7018-R electrode indicates the electrode must pass which test?
• Report conclusions should be phrased to avoid misinterpretation how?
• Which statement best describes how safety hazards should be prioritized during a Level 1 inspection?
• What is the primary purpose of CSA 178.2 Level 1?
• Why is documenting the exact location of deficiencies important?
• Which category does alloy steel belong to?
• Which standard contains requirements for the fabrication of steel bridges?
• Which carbon content range defines a hypoeutectoid steel?
• The CSA W47.1 welding procedure system consists of two components:
• GTAW electrodes used with 1% lanthanum are color coded Black.
• In the ASME Boiler and Pressure Vessel Code, which part covers Nonferrous Material Specifications?
• What is a prequalified joint?
• What is the inspector's obligation regarding safety during the inspection?
• Cold cracking occurs below what temperature?
• What role does standardization play in CSA 178.2 reporting?
• How should photos be labeled in the report?
• In the electrode designation E4918-X, what does the '490 MPa' indicate?
• Which statement best captures the purpose of the R suffix on electrodes like E7018-R?
• How should observed safety hazards be documented?
• Which element is used as an alloying element in steel and provides corrosion resistance?
• Which statement about a prequalified joint is accurate?
• Which statement is true regarding a CSA W47.1 Div. 1 certified company and staffing?
• Which part of the ASME Boiler and Pressure Vessel Code lists the specifications for welding electrodes and filler metals?
• What is the general approach to HVAC systems in Level 1?
• What does a signed client acknowledgment confirm?
• What should be included regarding shared systems observed on a party wall?
• What information should accompany each deficiency to aid remediation planning?
• A hypoeutectoid steel has:
• What is the storage temperature for low-hydrogen electrodes?
• How should liability concerns be addressed in the contract?
• Which statement best differentiates a defect and a deficiency?
• Which of the following is typically included as an interior feature?
• How should environmental hazards like mold be addressed in the report?
• What site condition considerations are included in the Level 1 inspection scope?
• How should the term “as inspected” be used in a report?
• What should be included in an inspection report’s photographs?
• Quality control is best described as:
• Structural standards tend to contain more stringent qualification and certification requirements than pressure vessel standards do regarding welder testing.
• Which statement best describes the R designation on E7018-R?
• The arc-start method with GTAW that has the highest cost is the Contact method/Lift start.
• What should be done if a critical safety issue is discovered after the inspection?
• According to CSA W59, what is the maximum allowable depth of undercut for a weld under cyclic loading where the load direction is transverse to the undercut?
• What roofing conditions are commonly identified in Level 1 inspections?
• In GTAW with direct current electrode negative (DCEN), what percentage of heat is deposited at the electrode and at the workpiece respectively?
• How should attic spaces be inspected and documented?
• In GMAW, the finger-like penetration profile is associated with Argon-rich shielding gas.
• According to CSA Standard W59, at what distance from the weld must the minimum preheat be maintained in 44 mm thick plate?
• What type of language is typically used in the liability disclaimer of the contract?
• Which statement best describes what Level 1 observations should focus on?
• If Charpy impact properties are a requirement of a welding procedure, then the:
• How should foundation and structural components be treated in a Level 1 inspection?
• Who is typically responsible for reporting observable conditions in a Level 1 inspection?
• How should insulation and ventilation be evaluated?
• CSA W59.2 Welded Aluminum Construction, allows the use of which welding process below?
• How is electrical safety evaluated in Level 1?
• Should refrigerant or fuel types be identified during a Level 1 inspection?
• When using radiography to inspect steel plate, hole-type IQIs are generally required to be placed:
• The supplier of a filler metal should provide documentation, such as a label on the package, that shows:
• In a DC welding circuit, the positive terminal is called the?
• CSA W59.2 is specifically for which materials?
• GTAW electrodes are classified under CSA Standard W48 using CAN/ISO 14341 designations. True or False?
• When a safety hazard is identified, what should the inspector do?
• Which standard/code covers the 'Design of Steel Structures'?
• How should windows and doors be assessed?
• First angle projection is commonly used in European drawings.
• What is the significance of the R in an E7018-R electrode?
• What does the 'R' suffix primarily relate to in welding electrode specifications?
• Which classification is required for a CSA W47.1 welder to perform complete joint penetration butt splices on tubular sections from one side?
• Which PPE item is appropriate for a Level 1 inspection when hazards are present?
• Which testing is indicated by the R suffix on a welding electrode designation?
• What is the recommended practice for keeping inspection records after completion?
• What describes the relationship of Level 1 inspections to warranties?
• In the electrode designation E7018-R, what does the R suffix imply?
• What is the proper handling of "non-permitted modifications" observed?
• How should the inspector interact with other professionals for follow-ups?
• The majority of welding-related standards in Canada are developed by the:
• The fume generation rate for a welding process is used to measure the welder's exposure to fume.
• In attic inspections, what should be documented?
• Which microstructure is formed when carbon content is up to 0.8% in steel under equilibrium?
• Which guideline describes how to prioritize time-sensitive issues?
• Low-hydrogen electrodes may be rebaked twice. True or False?
• If an area is inaccessible during a Level 1 inspection, what is the proper approach?
• How should a inspector handle high-risk indicators in tall structures or attics?
• What does a square symbol specify? (in welding symbols)
• The ductility of a sample transverse to the direction of rolling will be greater than a longitudinal sample.
• Which source recommends the types of ventilation to reduce welder exposure to welding fume?